Time-based control techniques for integrated DC-DC conversion

Time-based control techniques for the design of high switching frequency buck converters are presented. Using time as the processing variable, the proposed controller operates with CMOS-level digital-like signals but without adding any quantization error. A ring oscillator is used as an integrator in place of conventional opamp-RC or Gm-C integrators while a delay line is used to perform voltage-to-time conversion and to sum time signals. A simple flip-flop generates a pulse-width modulated signal from the time-based output of the controller. Hence time-based control eliminates the need for a wide bandwidth error amplifier, pulse width modulator (PWM) in analog controllers or high-resolution analog-to-digital converter (ADC) and digital PWM in digital controllers. As a result, it can be implemented in a small area and with minimal power. First, a time-based single-phase buck converter is proposed and fabricated in a 180nm CMOS process, the prototype buck converter occupies an active area of 0.24mm^2, of which the controller occupies only 0.0375mm^2. It operates over a wide range of switching frequencies (10-25 MHz) and regulates output to any desired voltage in the range of 0.6V to 1.5V with 1.8V input voltage. With a 500mA step in the load current, the settling time is less than 3.5us and the measured reference tracking bandwidth is about 1MHz. Better than 94% peak efficiency is achieved while consuming a quiescent current of only 2uA/MHz. Second, the techniques are extended to a high switching frequency multi-phase buck converter. Efficiency degradation due to mismatch between the phases is mitigated by generating precisely matched duty-cycles by combining a time-based multi-phase generator (MPG) with a time-based PID compensator (T-PID). The proposed approach obviates the need for a complex current sensing and calibration circuitry needed to implement active current sharing in an analog controller. It also eliminates the need for a high-resolution analog-to-digital converter and digital pulse width modulator needed for implementing passive current sharing in a digital controller. Fabricated in a 65nm CMOS process, the prototype multi-phase buck converter occupies an active area of 0.32mm^2, of which the controller occupies only 0.04mm^2. The converter operates over a wide range of switching frequencies (30-70 MHz) and regulates output to any desired voltage in the range of 0.6V to 1.5V from 1.8V input voltage. With a 400mA step in the load current, the settling time is less than 0.6us and the measured duty-cycle mismatch is less than 0.48%. Better than 87% peak efficiency is achieved while consuming a quiescent current of only 3uA/MHz. Finally, light load operation is discussed. The light load efficiency of a time-based buck converter is improved by adding proposed PFM control. At the same time, the proposed seamless transition techniques provide a freedom to change the control mode between PFM and PWM without deteriorating output voltage which allows for a system to manage its power efficiently. Fabricated in a 65nm CMOS, the prototype achieves 90% peak efficiency and > 80% efficiency over an ILOAD range of 2mA to 800mA. VO changes by less than 40mV during PWM to PFM transitions.

Name thesis:degree_name

Ph.D.

Level thesis:degree_level

Dissertation

Discipline thesis:degree_discipline

Electrical & Computer Engr

Grantor

University of Illinois at Urbana-Champaign

Year dc:date

2017

Author dc:creator

• Kim, Seong Joong

Contributors dc:contributor

• Hanumolu, Pavan Kumar
• Krein, Philip T.
• Shanbhag, Naresh R.
• Pilawa-Podgurski, Robert

• time-based
• DC-DC
• buck
• Proportional-Integral-Derivative (PID)
• Pulse-width modulator (PWM)
• Pulse frequency modulation (PFM)

Statement dc:rights

• Copyright 2016 Seong Joong Kim

Language dc:language

en

Handle dc:identifier

http://hdl.handle.net/2142/95566

OAI identifier oai:identifier

oai:www.ideals.illinois.edu:2142/95566