{"id":{"repo_id":"vt","oai_identifier":"oai:vtechworks.lib.vt.edu:10919/44491"},"canonical_url":"https://search.dev.ndltd.org/etd/vt/oai:vtechworks.lib.vt.edu:10919/44491","repository":{"repo_id":"vt","name":"Virginia Tech","base_url":"https://vtechworks.lib.vt.edu/oai/request"},"display":{"title":"A system identification technique for predicting transient operation of gas turbine engines","abstract":"A method for developing transient, predictive models of gas turbine engine performance using system identification techniques in conjunction with test cell data has been successfully demonstrated. Test cell data were obtained for both transient and steady-state operation from two F402-RR-406A USMC AV-8B engines at the Naval Aviation Depot (NADEP), Cherry Point, North Carolina. One engine was run to gather a single set of steady-state data consisting of 24 subsets of five seconds of data. The other engine was run to obtain two sets of transient data, recorded at three different rates of engine acceleration for each set. The acceleration rates of 3, 25, and 100 degrees of throttle per second were preset in the test cell controls. These rates correspond to the angular velocity of the fuel throttle during an acceleration. Each of these six transient test runs consisted of 25 seconds of data. Data were captured at a rate of five Hertz over the engine operating range from idle (26% Low Pressure spool speed) to full military power (105% LP spool speed) for all cases. A BASIC code developed at the NADEP required significant modification before it could be used to reduce the data. The modified code generated engine operating points consisting of mass flow rate, total pressure ratio, spool speed, and rate of acceleration for the inner fan, outer fan, and high pressure compressor. Finally, a multivariate regression technique using the SAS language was developed in cooperation with the Virginia Tech Statistical Consulting Center. This technique was used to generate a closed-form model of each component capable of predicting operating points at spool speeds and acceleration rates intermediate to those measured.","abstract_html":"A method for developing transient, predictive models of gas turbine engine performance using system identification techniques in conjunction with test cell data has been successfully demonstrated. Test cell data were obtained for both transient and steady-state operation from two F402-RR-406A USMC AV-8B engines at the Naval Aviation Depot (NADEP), Cherry Point, North Carolina. One engine was run to gather a single set of steady-state data consisting of 24 subsets of five seconds of data. The other engine was run to obtain two sets of transient data, recorded at three different rates of engine acceleration for each set. The acceleration rates of 3, 25, and 100 degrees of throttle per second were preset in the test cell controls. These rates correspond to the angular velocity of the fuel throttle during an acceleration. Each of these six transient test runs consisted of 25 seconds of data. Data were captured at a rate of five Hertz over the engine operating range from idle (26% Low Pressure spool speed) to full military power (105% LP spool speed) for all cases. A BASIC code developed at the NADEP required significant modification before it could be used to reduce the data. The modified code generated engine operating points consisting of mass flow rate, total pressure ratio, spool speed, and rate of acceleration for the inner fan, outer fan, and high pressure compressor. Finally, a multivariate regression technique using the SAS language was developed in cooperation with the Virginia Tech Statistical Consulting Center. This technique was used to generate a closed-form model of each component capable of predicting operating points at spool speeds and acceleration rates intermediate to those measured.","abstract_has_math":false,"creators":["Grose, Michael David"],"institution":"Virginia Tech","degree_name":"Master of Science","degree_level":"masters","degree_discipline":"Mechanical Engineering","degree_department":"Mechanical Engineering","school":null,"contributors":[],"advisors":[],"committee_chairs":["O'Brien, Walter F. Jr."],"committee_members":["Mitchell, Larry D.","Ng, Fai"],"year":1996,"date_issued":"1996-11-05","date_published":"1996-11-05","updated_at":"2026-07-22T22:19:48Z","subjects":["gas turbine","system identification","transient"],"languages":["en"],"rights":["In Copyright"],"rights_urls":["http://rightsstatements.org/vocab/InC/1.0/"],"identifier_entries":[{"key":"dc:identifier.other","label":"Dc Identifier Other","values":["etd-08292008-063402"],"render_values":[{"text":"etd-08292008-063402","href":null,"code":true}]}]},"links":{"outbound_url":"http://hdl.handle.net/10919/44491","outbound_label":"Handle","outbound_source":"dc:identifier.uri"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor.committeechair","label":"Committee Chair","values":["O'Brien, Walter F. Jr."]},{"key":"dc:contributor.committeemember","label":"Committee Member","values":["Mitchell, Larry D.","Ng, Fai"]},{"key":"dc:contributor.department","label":"Department","values":["Mechanical Engineering"]},{"key":"dc:creator","label":"Author","values":["Grose, Michael David"]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date.accessioned","label":"Dc Date Accessioned","values":["2014-03-14T21:44:01Z"]},{"key":"dc:date.available","label":"Dc Date Available","values":["2014-03-14T21:44:01Z","2008-08-29"]},{"key":"dc:date.issued","label":"Date","values":["1996-11-05"]},{"key":"dc:publisher","label":"Institution","values":["Virginia Tech"]},{"key":"dc:type","label":"Dc Type","values":["Thesis"]},{"key":"dc:type.dcmitype","label":"Dc Type Dcmitype","values":["Text"]},{"key":"thesis:degree_discipline","label":"Discipline","values":["Mechanical Engineering"]},{"key":"thesis:degree_level","label":"Degree Level","values":["masters"]},{"key":"thesis:degree_name","label":"Degree Name","values":["Master of Science"]},{"key":"thesis:institution_name","label":"Thesis Institution Name","values":["Virginia Polytechnic Institute and State University"]}]},{"id":"subjects_keywords","label":"Subjects and Keywords","entries":[{"key":"dc:subject","label":"Dc Subject","values":["gas turbine","system identification","transient"]}]},{"id":"language_rights","label":"Language and Rights","entries":[{"key":"dc:language.iso","label":"Language (ISO)","values":["en"]},{"key":"dc:rights","label":"Dc Rights","values":["In Copyright"]},{"key":"dc:rights.uri","label":"Rights URI","values":["http://rightsstatements.org/vocab/InC/1.0/"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier.other","label":"Dc Identifier Other","values":["etd-08292008-063402"]},{"key":"dc:identifier.uri","label":"Identifier URI","values":["http://hdl.handle.net/10919/44491"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description.abstract","label":"Abstract","values":["A method for developing transient, predictive models of gas turbine engine performance using system identification techniques in conjunction with test cell data has been successfully demonstrated. Test cell data were obtained for both transient and steady-state operation from two F402-RR-406A USMC AV-8B engines at the Naval Aviation Depot (NADEP), Cherry Point, North Carolina. One engine was run to gather a single set of steady-state data consisting of 24 subsets of five seconds of data. The other engine was run to obtain two sets of transient data, recorded at three different rates of engine acceleration for each set. The acceleration rates of 3, 25, and 100 degrees of throttle per second were preset in the test cell controls. These rates correspond to the angular velocity of the fuel throttle during an acceleration. Each of these six transient test runs consisted of 25 seconds of data. Data were captured at a rate of five Hertz over the engine operating range from idle (26% Low Pressure spool speed) to full military power (105% LP spool speed) for all cases. A BASIC code developed at the NADEP required significant modification before it could be used to reduce the data. The modified code generated engine operating points consisting of mass flow rate, total pressure ratio, spool speed, and rate of acceleration for the inner fan, outer fan, and high pressure compressor. Finally, a multivariate regression technique using the SAS language was developed in cooperation with the Virginia Tech Statistical Consulting Center. This technique was used to generate a closed-form model of each component capable of predicting operating points at spool speeds and acceleration rates intermediate to those measured."]},{"key":"dc:description.degree","label":"Dc Description Degree","values":["Master of Science"]},{"key":"dc:format.medium","label":"Dc Format Medium","values":["BTD"]},{"key":"dc:format.mimetype","label":"Dc Format Mimetype","values":["application/pdf"]},{"key":"dc:title","label":"Title","values":["A system identification technique for predicting transient operation of gas turbine engines"]}]}],"canonical_facts":{"dc:contributor.committeechair":["O'Brien, Walter F. Jr."],"dc:contributor.committeemember":["Mitchell, Larry D.","Ng, Fai"],"dc:contributor.department":["Mechanical Engineering"],"dc:creator":["Grose, Michael David"],"dc:date.accessioned":["2014-03-14T21:44:01Z"],"dc:date.available":["2014-03-14T21:44:01Z","2008-08-29"],"dc:date.issued":["1996-11-05"],"dc:description.abstract":["A method for developing transient, predictive models of gas turbine engine performance using system identification techniques in conjunction with test cell data has been successfully demonstrated. Test cell data were obtained for both transient and steady-state operation from two F402-RR-406A USMC AV-8B engines at the Naval Aviation Depot (NADEP), Cherry Point, North Carolina. One engine was run to gather a single set of steady-state data consisting of 24 subsets of five seconds of data. The other engine was run to obtain two sets of transient data, recorded at three different rates of engine acceleration for each set. The acceleration rates of 3, 25, and 100 degrees of throttle per second were preset in the test cell controls. These rates correspond to the angular velocity of the fuel throttle during an acceleration. Each of these six transient test runs consisted of 25 seconds of data. Data were captured at a rate of five Hertz over the engine operating range from idle (26% Low Pressure spool speed) to full military power (105% LP spool speed) for all cases. A BASIC code developed at the NADEP required significant modification before it could be used to reduce the data. The modified code generated engine operating points consisting of mass flow rate, total pressure ratio, spool speed, and rate of acceleration for the inner fan, outer fan, and high pressure compressor. Finally, a multivariate regression technique using the SAS language was developed in cooperation with the Virginia Tech Statistical Consulting Center. This technique was used to generate a closed-form model of each component capable of predicting operating points at spool speeds and acceleration rates intermediate to those measured."],"dc:description.degree":["Master of Science"],"dc:format.medium":["BTD"],"dc:format.mimetype":["application/pdf"],"dc:identifier.other":["etd-08292008-063402"],"dc:identifier.uri":["http://hdl.handle.net/10919/44491"],"dc:language.iso":["en"],"dc:publisher":["Virginia Tech"],"dc:rights":["In Copyright"],"dc:rights.uri":["http://rightsstatements.org/vocab/InC/1.0/"],"dc:subject":["gas turbine","system identification","transient"],"dc:title":["A system identification technique for predicting transient operation of gas turbine engines"],"dc:type":["Thesis"],"dc:type.dcmitype":["Text"],"thesis:degree_discipline":["Mechanical Engineering"],"thesis:degree_level":["masters"],"thesis:degree_name":["Master of Science"],"thesis:institution_name":["Virginia Polytechnic Institute and State University"]},"updated_at":"2026-07-22T22:19:48Z"}