{"id":{"repo_id":"vt","oai_identifier":"oai:vtechworks.lib.vt.edu:10919/36461"},"canonical_url":"https://search.dev.ndltd.org/etd/vt/oai:vtechworks.lib.vt.edu:10919/36461","repository":{"repo_id":"vt","name":"Virginia Tech","base_url":"https://vtechworks.lib.vt.edu/oai/request"},"display":{"title":"Evaluation of a Strut-Plasma Torch Combination as a Supersonic Igniter-Flameholder","abstract":"As the flight speeds of aircraft are increased above Mach 5, efficient methods of propulsion are needed. Scramjets may be a solution to this problem. Supersonic combustion is one of the main challenges involved in the operation of a Scramjet engine. In general, both an igniter and a flameholder are needed to achieve and maintain supersonic combustion. The current work examines a plasma torch-strut combination as an igniter-flameholder. The plasma torch-strut combination was tested in the Virginia Tech unheated supersonic wind tunnel at Mach 2.4. Pressure and temperature sampling, filtered photography, and spectroscopic measurements were used to compare different test cases. These results provide both qualitative and quantitative results on how the combination responds to changes in the mass flow rate of fuel and the power to the plasma torch. The key conclusions of the work were the following: 1. Tests showed that an exothermic reaction takes place. 2. The amount of heat release increases with an increase in the mass flow rate of fuel. 3. The plasma torch-fuel injector interaction caused the heat release to be well above the tunnel floor and sometimes off the strut centerline 4. One change in the fuel injector pattern caused more temperature rise near the floor of the tunnel. 5. The flow penetration height of the plasma torch alone was reduced by the fuel-plasma torch interaction. 6. Moving the strut upstream reduced the measured temperature rise at a fixed downstream location, but increased the penetration height of the plasma torch. 7. The computed heat release was found to be small compared to the potential heat release from all the fuel burning. 8. The amount of temperature rise caused by the fuel is not greatly affected by the power to the plasma torch.","abstract_html":"As the flight speeds of aircraft are increased above Mach 5, efficient methods of propulsion are needed. Scramjets may be a solution to this problem. Supersonic combustion is one of the main challenges involved in the operation of a Scramjet engine. In general, both an igniter and a flameholder are needed to achieve and maintain supersonic combustion. The current work examines a plasma torch-strut combination as an igniter-flameholder. The plasma torch-strut combination was tested in the Virginia Tech unheated supersonic wind tunnel at Mach 2.4. Pressure and temperature sampling, filtered photography, and spectroscopic measurements were used to compare different test cases. These results provide both qualitative and quantitative results on how the combination responds to changes in the mass flow rate of fuel and the power to the plasma torch. The key conclusions of the work were the following: 1. Tests showed that an exothermic reaction takes place. 2. The amount of heat release increases with an increase in the mass flow rate of fuel. 3. The plasma torch-fuel injector interaction caused the heat release to be well above the tunnel floor and sometimes off the strut centerline 4. One change in the fuel injector pattern caused more temperature rise near the floor of the tunnel. 5. The flow penetration height of the plasma torch alone was reduced by the fuel-plasma torch interaction. 6. Moving the strut upstream reduced the measured temperature rise at a fixed downstream location, but increased the penetration height of the plasma torch. 7. The computed heat release was found to be small compared to the potential heat release from all the fuel burning. 8. The amount of temperature rise caused by the fuel is not greatly affected by the power to the plasma torch.","abstract_has_math":false,"creators":["Mozingo, Joseph Alexander"],"institution":"Virginia Tech","degree_name":"Master of Science","degree_level":"masters","degree_discipline":"Mechanical Engineering","degree_department":"Mechanical Engineering","school":null,"contributors":[],"advisors":[],"committee_chairs":["O'Brien, Walter F. Jr."],"committee_members":["Vandsburger, Uri","Schetz, Joseph A."],"year":2004,"date_issued":"2004-02-23","date_published":"2004-02-23","updated_at":"2026-07-22T22:19:03Z","subjects":["strut","plasma torch","supersonic combustion"],"languages":[],"rights":["In Copyright"],"rights_urls":["http://rightsstatements.org/vocab/InC/1.0/"],"identifier_entries":[{"key":"dc:identifier.other","label":"Dc Identifier Other","values":["etd-12272005-111912"],"render_values":[{"text":"etd-12272005-111912","href":null,"code":true}]}]},"links":{"outbound_url":"http://hdl.handle.net/10919/36461","outbound_label":"Handle","outbound_source":"dc:identifier.uri"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor.committeechair","label":"Committee Chair","values":["O'Brien, Walter F. Jr."]},{"key":"dc:contributor.committeemember","label":"Committee Member","values":["Vandsburger, Uri","Schetz, Joseph A."]},{"key":"dc:contributor.department","label":"Department","values":["Mechanical Engineering"]},{"key":"dc:creator","label":"Author","values":["Mozingo, Joseph Alexander"]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date.accessioned","label":"Dc Date Accessioned","values":["2014-03-14T20:50:50Z"]},{"key":"dc:date.available","label":"Dc Date Available","values":["2014-03-14T20:50:50Z","2006-03-15"]},{"key":"dc:date.issued","label":"Date","values":["2004-02-23"]},{"key":"dc:publisher","label":"Institution","values":["Virginia Tech"]},{"key":"dc:type","label":"Dc Type","values":["Thesis"]},{"key":"thesis:degree_discipline","label":"Discipline","values":["Mechanical Engineering"]},{"key":"thesis:degree_level","label":"Degree Level","values":["masters"]},{"key":"thesis:degree_name","label":"Degree Name","values":["Master of Science"]},{"key":"thesis:institution_name","label":"Thesis Institution Name","values":["Virginia Polytechnic Institute and State University"]}]},{"id":"subjects_keywords","label":"Subjects and Keywords","entries":[{"key":"dc:subject","label":"Dc Subject","values":["strut","plasma torch","supersonic combustion"]}]},{"id":"language_rights","label":"Language and Rights","entries":[{"key":"dc:rights","label":"Dc Rights","values":["In Copyright"]},{"key":"dc:rights.uri","label":"Rights URI","values":["http://rightsstatements.org/vocab/InC/1.0/"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier.other","label":"Dc Identifier Other","values":["etd-12272005-111912"]},{"key":"dc:identifier.uri","label":"Identifier URI","values":["http://hdl.handle.net/10919/36461"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description.abstract","label":"Abstract","values":["As the flight speeds of aircraft are increased above Mach 5, efficient methods of propulsion are needed. Scramjets may be a solution to this problem. Supersonic combustion is one of the main challenges involved in the operation of a Scramjet engine. In general, both an igniter and a flameholder are needed to achieve and maintain supersonic combustion. The current work examines a plasma torch-strut combination as an igniter-flameholder. The plasma torch-strut combination was tested in the Virginia Tech unheated supersonic wind tunnel at Mach 2.4. Pressure and temperature sampling, filtered photography, and spectroscopic measurements were used to compare different test cases. These results provide both qualitative and quantitative results on how the combination responds to changes in the mass flow rate of fuel and the power to the plasma torch. The key conclusions of the work were the following: 1. Tests showed that an exothermic reaction takes place. 2. The amount of heat release increases with an increase in the mass flow rate of fuel. 3. The plasma torch-fuel injector interaction caused the heat release to be well above the tunnel floor and sometimes off the strut centerline 4. One change in the fuel injector pattern caused more temperature rise near the floor of the tunnel. 5. The flow penetration height of the plasma torch alone was reduced by the fuel-plasma torch interaction. 6. Moving the strut upstream reduced the measured temperature rise at a fixed downstream location, but increased the penetration height of the plasma torch. 7. The computed heat release was found to be small compared to the potential heat release from all the fuel burning. 8. The amount of temperature rise caused by the fuel is not greatly affected by the power to the plasma torch."]},{"key":"dc:description.degree","label":"Dc Description Degree","values":["Master of Science"]},{"key":"dc:title","label":"Title","values":["Evaluation of a Strut-Plasma Torch Combination as a Supersonic Igniter-Flameholder"]}]}],"canonical_facts":{"dc:contributor.committeechair":["O'Brien, Walter F. Jr."],"dc:contributor.committeemember":["Vandsburger, Uri","Schetz, Joseph A."],"dc:contributor.department":["Mechanical Engineering"],"dc:creator":["Mozingo, Joseph Alexander"],"dc:date.accessioned":["2014-03-14T20:50:50Z"],"dc:date.available":["2014-03-14T20:50:50Z","2006-03-15"],"dc:date.issued":["2004-02-23"],"dc:description.abstract":["As the flight speeds of aircraft are increased above Mach 5, efficient methods of propulsion are needed. Scramjets may be a solution to this problem. Supersonic combustion is one of the main challenges involved in the operation of a Scramjet engine. In general, both an igniter and a flameholder are needed to achieve and maintain supersonic combustion. The current work examines a plasma torch-strut combination as an igniter-flameholder. The plasma torch-strut combination was tested in the Virginia Tech unheated supersonic wind tunnel at Mach 2.4. Pressure and temperature sampling, filtered photography, and spectroscopic measurements were used to compare different test cases. These results provide both qualitative and quantitative results on how the combination responds to changes in the mass flow rate of fuel and the power to the plasma torch. The key conclusions of the work were the following: 1. Tests showed that an exothermic reaction takes place. 2. The amount of heat release increases with an increase in the mass flow rate of fuel. 3. The plasma torch-fuel injector interaction caused the heat release to be well above the tunnel floor and sometimes off the strut centerline 4. One change in the fuel injector pattern caused more temperature rise near the floor of the tunnel. 5. The flow penetration height of the plasma torch alone was reduced by the fuel-plasma torch interaction. 6. Moving the strut upstream reduced the measured temperature rise at a fixed downstream location, but increased the penetration height of the plasma torch. 7. The computed heat release was found to be small compared to the potential heat release from all the fuel burning. 8. The amount of temperature rise caused by the fuel is not greatly affected by the power to the plasma torch."],"dc:description.degree":["Master of Science"],"dc:identifier.other":["etd-12272005-111912"],"dc:identifier.uri":["http://hdl.handle.net/10919/36461"],"dc:publisher":["Virginia Tech"],"dc:rights":["In Copyright"],"dc:rights.uri":["http://rightsstatements.org/vocab/InC/1.0/"],"dc:subject":["strut","plasma torch","supersonic combustion"],"dc:title":["Evaluation of a Strut-Plasma Torch Combination as a Supersonic Igniter-Flameholder"],"dc:type":["Thesis"],"thesis:degree_discipline":["Mechanical Engineering"],"thesis:degree_level":["masters"],"thesis:degree_name":["Master of Science"],"thesis:institution_name":["Virginia Polytechnic Institute and State University"]},"updated_at":"2026-07-22T22:19:03Z"}