Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 35 for “"Flexural Modulus"”.
-
Flexural behavior of a glass fiber reinforced wood fiber composite
The static and dynamic flexural properties of a wood fiber matrix internally reinforced with continuous glass fibers were investigated. When modelled as a sandwich composite, the static flexural modulus of elasticity (MOE) of glass fiber reinforced hardboard could be successfully predicted from the …
-
Structure property relationships in polyolefins
… A decrease in the heat of fusion, yield stress, flexural modulus has been observed with increasing rubber content. The addition of nucleating agents however, caused an increase in the crystallization temperature, heat of fusion, yield stress, flexural modulus, and rigid fraction.
-
Mechanical Performance of Industrial Hemp Fibre Reinforced Polylactide and Unsaturated Polyester Composites
… cellulose crystallinity. The average Young's modulus and thermal stability of all treated fibres increased compared with untreated fibres. This was considered to be as a result of densification of fibre cell walls due to the removal of non-cellulosic components during treatment. It was also …
-
Re-strengthening demineralized bone via tannin-iron crosslinking
… coating results in a 1062% increase in the flexural modulus for fully hydrated and demineralized bone.
-
Development of a new method for fibre reinforced rotational moulding
… to woven fabric. Mouldings were tested for flexural properties, impact properties and Inter Laminar Shear Strength. The best results were found for woven PP-Twintex fabric and PP/glass melt impregnated tape in polypropylene. In the latter case, the Flexural Modulus measured was the same as …
-
Characterization and development of polycaprolactone (PCL)/montmorillonite (MMT)/hydroxapaptite (HA) nano-composites for fused deposition modelling (FDM) process
… mechanical properties were assessed by tensile, flexural and charpy impact tests while the thermal properties were studied via differential scanning calorimetry (DSC) and thermogravimetry analyzer (TGA). Simulated body fluid (SBF) test was used to assess the bioactivity properties of the …
-
Silicone resins and their composites
… with temperature. Properties include maximum flexural stress, flexural modulus and fracture toughness K[sub]IC. Temperature effect on mechanical properties of addition cure resin is substantial and also depends on the crosslinkers used. Generally the maximum stress and flexural modulus …
-
Rotational Molding of Acrylonitrile-Butadiene-Styrene Polymers and Blends
… 3,300 psi). Larger differences were observed in flexural modulus (200,000 psi to 110,000 psi) and heat distortion temperature (95°C to 61°C). Therefore, these formulation and processing changes show a trade-off where stiffness and thermal stability (i.e. flexural modulus and heat distortion …
-
The effect of polymerization methods and fiber types on the mechanical behavior of fiber-reinforced composite resin
… or two-step). Specimens were tested for flexural strength, flexural modulus, and microhardness. The failure modes of specimens were observed by scanning electron microscopy (SEM). Results: The fiber types showed significant effect on the flexural strength of test specimens (F = 469.48; p …
-
Adhesion of Orthodontic Cements Formulated with Microencapsulated Remineralizing Agents
… mechanism of failure. Shear bond strength and flexural modulus measurements were determined along with optical microscopy to study the effect of microcapsules on adhesion in an orthodontic cement.
-
Genesis : the search for origins : the curation and contamination control of returned solar wind samples
… heating effects. A procedure to measure the flexural modulus of samples was proposed to quantify the success of the optimisation of the scribing parameters. A theoretical study was carried out to develop a predictive kinetic model for the oxidation of the silicon collector arrays during …
-
Experimental Investigation Of Fatigue Behavior Of Carbon Fiber Composites Using Fully-Reversed Four-Point Bending Test
… a maximum stress of about 200 MPa. The decay in flexural modulus of the beam as it goes under cyclic loading was calculated and it was seen that flexural modulus shows an exponential decay which can be expressed as: E = E<sub>0</sub>e<super>AN</super>. Four–point bending fatigue tests were …
-
Large deformation dynamic bending of composite beams
… exhibited bimodular properties. The compressive flexural moduli in some laminates was measured to be 1/2 the tensile flexural modulus. No simple relationship could be found among the measured ultimate failure strains of the different laminate types. Using empirically determined flexural …
-
Properties constrained cost optimization of polyester-filler systems with non-linear property-composition relationships
… standard methods to obtain the density, tensile, flexural and compression strengths, secant and flexural moduli and ultimate elongation. Multiple regression analysis yielded satisfactory regression coefficients for all properties except the flexural modulus and ultimate elongation. Linear …
-
Synthesis and Characterization of Phosphine Oxide Containing Monomers and of the Flame Resistant Polymers Prepared Therefrom
… decreases in other characteristics such as flexural modulus. Reactive systems also maintained chemical resistance in contrast to non-reactive thermoplastic controls.
-
Ionic liquids as additives for biodegradable polyactic acid
… anion containing IL reduced the flexural modulus and strength of PLA, affecting much less its ductility than the decanoate anion containing IL.
-
Understanding the Effect of Sizing and Cellulose Nanocrystals on S2 Glass Fiber Sheet Molding Compounds
… are not performing as carbon fibers in terms of modulus, strength, or density, but they are seen as an alternative to E-glass fibers when carbon fibers are not an option. The question of interest is whether the performance of S2 glass fibers structural composites has reached its plateau or if …
-
Nanoparticles as strengthening agents in polymer systems
… dispersed in PPF/PPF-DA exhibited increased flexural modulus compared to polymer resin alone, and a significant enhancement over both the activated and surfacted alumoxanes. Boric acid is used as the cross-linking agent in oil well drilling industry even though the efficacy of the borate ion, …
-
A novel polymeric prosthetic heart valve: design, manufacture, and testing
… novel material performance index comprising the flexural modulus and the cyclic fatigue stress predicted by fracture mechanics methods. Polystyrene-block-polyethylene-polypropylene-block-polystyrene with 22 mol% polystyrene (SEPS22) was selected for further testing and use in the design. …
-
Tribology in coal-fired power plants
… and mechanical properties including hardness, flexural modulus and flexural strengths. The erosion rates of the tested alumina ceramics increase with an increase in the impact angle, reaching a maximum at 90°. The high purity 96% alumina dry-pressed body has the best erosion resistance at most …
Page 1 of 2